Operation of riveting machine

The power supply of this machine is 380V. This model is suitable for riveting of luggage, furniture, sports equipment, catering equipment industry, bicycle accessories, various hardware and other industries. Please check and connect the correct power supply when connecting to the electricity, otherwise the motor will be damaged. The routine adjustment and maintenance steps of the machine are as follows:

  1. First, add lubricating oil to the moving part and the oil filling port to ensure the smooth operation of the machine. In the case of no power, check whether the upper and lower molds are aligned and the distance is correct: step on the footboard and pull the flywheel by hand to make the upper and lower molds close to the position, and check whether the upper, lower, left, and right molds are in the center position and the distance between the upper and lower molds is correct. Turn the flywheel upper die axis to reset, and visually check whether the duckbill nail inlet and the runner are aligned. If not, please adjust to the correct position. After the adjustment is OK, the debris in the runner, duckbill, and upper and lower molds should be removed to keep all parts clean and smooth.

  2. When starting up, if it is a 380V power supply, you need to check whether the direction of rotation is correct? Otherwise, please adjust to the correct position, and then place the rivets in the funnel. The rivets should be 1/3-1/2 of the capacity of the bowl. Too much will cause jamming.

　　3. Idling the test machine for 3-5 minutes, after confirming that everything is normal, it can work.

　　4. How to solve the common problems of the machine:

　　A: Causes of duckbill turning nails, nails falling out, and nails clamped and eliminated:

　　① Adjusting the adjusting bolt on the duckbill rod to be too high or too low will cause the duckbill to open early or late, which will cause the nail turning or nail drop phenomenon and the nail clamping phenomenon. Adjust it according to the actual situation to eliminate the fault;

　　②The internal spring of the duckbill is fatigued or failed, and a new one needs to be replaced at this time;

　　 The misalignment of the runner opening and the duckbill nail inlet will cause the nail to turn, and it needs to be realigned.

　　B: The cause and elimination of the stuck funnel:

　　①Due to wear and tear in use, the gap between the small crescent eyebrow and the bowl male becomes larger, and the rivet can be flipped between the gaps. If it is stuck between the small crescent eyebrow and bowl male, the gap needs to be re-adjusted. If the adjustment is not good, it needs to be replaced with a new one;

②Due to long-term use, the gap between the bowl and the funnel seat becomes larger, and the rivets are easy to turn over and cause jamming. At this time, the funnel seat needs to be disassembled and the base surface is re-flattened. If the problem cannot be solved, replace the bowl with a new one. Can

　　③The rotating speed of the bowl shaft is too high, which will cause the rivets to fly up, and it is easy to produce nails. Adjust the bowl shaft to a suitable rotating speed (see the instructions for adjusting the speed of missing nails).

　　C: The rivet is skewed after forming:

　　①The center of the lower mold and the upper mold are not aligned, just re-align it;

　　②The end face of the upper die is worn out, making it poorly matched with the nail cap, and the upper die needs to be re-dressed or replaced with a new one.

　　D: The rivet rolls badly, and the roll mouth blooms:

　　①If it is a new machine, it is badly manufactured, and it will be replaced with a new one free of charge;

　　②Long-term use, the shape of the lower die roll mouth wears out, replace it with a new one.

　　 5. Do not put your hands between the upper and lower molds at any time to avoid unnecessary personal injury.

　　6. After the work is finished, the residue and dirt in the runner, duckbill and upper and lower molds should be removed, and the whole machine should be cleaned, and lubricating oil (grease) should be added to ensure the normal accuracy of the machine and prolong its service life.